Safety rules and apparatus names, preparing and collecting the common gases and identifying them (O₂, H₂, CO₂, NH₃, Cl₂), separation and purification methods, and measurement errors.
Rules that keep appearing in exam items: never heat a closed tube, never smell a gas directly, light the Bunsen burner before opening the gas fully, and dispose of chemicals in the designated containers.
Measurement errors: zero error, parallax (eye not level with the meniscus), and transfer loss — all three make the read volume too small when uncorrected.
| Apparatus | Main use | Do not |
|---|---|---|
| Test tube | small-scale reactions; heating small amounts of solid or liquid | fill more than one third; heat one spot only — move it through the flame |
| Boiling tube | heating larger volumes; small-scale gas preparation | point the mouth at anyone while heating |
| Conical flask | swirling a reaction mixture; titration; holding the filtrate | heat to dryness; use it to measure an accurate volume |
| Volumetric flask | making one fixed volume of solution of known concentration | heat it; run a reaction in it; store alkali in it for long (the neck is etched) |
| Beaker | mixing, dissolving, rough volumes | read a volume from it — the graduations are only about ±5% |
| Measuring cylinder | measuring a volume to about ±1% | heat it; read it with the eye above or below the meniscus |
| Burette | delivering a variable, accurate volume during a titration | fill above the tap; leave alkali in it for days (the tap seizes) |
| Pipette (25.00 mL) | delivering one accurate fixed volume | blow out the last drop; pipette a hot liquid |
| Dropping funnel | adding a liquid slowly and under control | leave the tap open when heating stops — suck-back follows |
| Evaporating dish | evaporating a solvent to concentrate a solution | evaporate to complete dryness if the solid decomposes on strong heating |
| Filter funnel and paper | separating an insoluble solid from a liquid | pour above the top edge of the paper; stir inside the cone |
| Retort stand, clamp, boss | holding apparatus steady | clamp a hot flask with bare fingers |
| Analytical balance | weighing to 0.0001 g | weigh a hot object; put chemicals directly on the pan |
| Gas jar | collecting and storing a gas | leave an open jar of a toxic gas on the bench |
Water and most aqueous solutions wet glass, so the surface curves down at the edges and the lowest point of the curve is the true level. Stand the cylinder on a flat bench, bring your eye level with the meniscus — not above it, not below it — and read the bottom of the curve. For a dark or opaque liquid read the top of the meniscus; for mercury, which does not wet glass, read the top of the dome. Estimate one digit beyond the smallest division: a cylinder marked every 1 mL is read to 0.1 mL, and a burette marked every 0.1 mL to 0.05 mL. Always write the unit, and write as many decimal places as the instrument justifies — "20.0 mL" is a measurement, while "20 mL" hides the precision.
| Type | Cause | Effect on the reading | How to deal with it |
|---|---|---|---|
| Systematic — zero error | the instrument does not read zero when empty: liquid below the burette tap, a balance that was not tared | every reading is shifted the same way, by the same amount | check the zero before use; subtract the blank |
| Systematic — parallax | the eye is not level with the meniscus | all readings too high, or all too low, depending on which side you read from | read at eye level; use a meniscus card behind the burette |
| Systematic — transfer loss | liquid left in the pipette or beaker, solid left on the weighing paper | the amount that reaches the flask is less than the amount calculated | rinse with the receiving solvent; transfer quantitatively |
| Random | judgement of the last digit, small temperature drift | readings scatter on both sides of the true value | repeat and average; control the temperature |
| Gross (personal) | misreading the scale, writing the wrong unit, using the wrong graduation | a large one-off error, easy to spot | re-read, check the unit, ask a second observer |
A systematic error does not cancel when you average — repeat the reading and the same offset is still there. A random error does cancel, which is exactly why three concordant titres are averaged.
| Gas | Reaction | Collection | Test |
|---|---|---|---|
| O₂ | 2KClO₃ → 2KCl + 3O₂ (MnO₂ catalyst, heat) | water displacement or upward air | relights a glowing splint |
| H₂ | Zn + H₂SO₄ → ZnSO₄ + H₂ | downward air displacement | pops with a flame |
| CO₂ | CaCO₃ + 2HCl → CaCl₂ + H₂O + CO₂ | upward air displacement | turns limewater milky |
| NH₃ | 2NH₄Cl + Ca(OH)₂ → CaCl₂ + 2NH₃ + 2H₂O | downward air displacement | turns damp red litmus blue |
| Cl₂ | MnO₂ + 4HCl → MnCl₂ + Cl₂ + 2H₂O | upward air displacement | bleaches damp litmus |
Collection rule: a gas lighter than air is collected by downward displacement, a heavier one upward, and a gas sparingly soluble in water by water displacement.
Preparation. Heat potassium chlorate with manganese(IV) oxide. The oxide is a catalyst: it offers an alternative pathway of lower activation energy, and it is recovered unchanged at the end of the reaction.
\(2KClO_3 (s) → 2KCl (s) + 3O_2 (g)\) conditions: strong heating, \(MnO_2\) catalyst.
Other routes: \(2KMnO_4 (s) → K_2MnO_4 (s) + MnO_2 (s) + O_2 (g)\) needs no catalyst, and \(2H_2O_2 (aq) → 2H_2O (l) + O_2 (g)\) with \(MnO_2\) runs at room temperature.
Collection. Over water, because \(O_2\) is only sparingly soluble (about 0.03 volumes per volume of water at 20 °C) and this gives the purest sample; or by upward displacement of air, because \(M_r = 32\) against 29 for air, a density ratio of 1.10.
Test. A glowing splint relights. The higher concentration of oxygen makes the combustion of the wood fast enough to produce a flame instead of a glow.
Drying. Concentrated \(H_2SO_4\) or anhydrous \(CaCl_2\); both are unreactive toward oxygen.
Preparation. Zinc granules with dilute sulfuric acid (about 1 M). The reaction is exothermic and starts without heating; copper is not used because it lies below hydrogen in the reactivity series and does not displace it.
\(Zn (s) + H_2SO_4 (aq) → ZnSO_4 (aq) + H_2 (g)\) or \(Zn (s) + 2HCl (aq) → ZnCl_2 (aq) + H_2 (g)\).
Collection. Downward displacement of air (\(M_r = 2\), density ratio 0.069) or over water (very sparingly soluble, 0.018 volumes per volume). Never collect it in a closed vessel: the mixture with air explodes over a wide range of compositions.
Test. A lighted splint held at the mouth gives a squeaky pop — the small explosion of the mixture burning at once.
Drying. Concentrated \(H_2SO_4\), anhydrous \(CaCl_2\) or \(CaO\); hydrogen is not acidic or basic, so all three are safe.
Preparation. Marble chips (calcium carbonate) with dilute hydrochloric acid. Chips rather than powder keep the rate controllable; the Kipp apparatus uses the same reaction and can be stopped by closing the tap.
\(CaCO_3 (s) + 2HCl (aq) → CaCl_2 (aq) + H_2O (l) + CO_2 (g)\).
Dilute sulfuric acid is not used with marble: the calcium sulfate that forms is only slightly soluble, coats the chips and the reaction stops.
Collection. Upward displacement of air: \(M_r = 44\), density ratio 1.52. Not over water, because \(CO_2\) dissolves appreciably (about 0.9 volumes per volume) and some of it reacts to give carbonic acid.
Test. Bubble the gas through limewater: it turns milky, \(Ca(OH)_2 (aq) + CO_2 (g) → CaCO_3 (s) + H_2O (l)\). With a large excess of \(CO_2\) the precipitate redissolves as calcium hydrogencarbonate, \(CaCO_3 (s) + H_2O (l) + CO_2 (g) → Ca(HCO_3)_2 (aq)\) — so "milky then clear" still confirms \(CO_2\).
Drying. Concentrated \(H_2SO_4\) only, of the common agents. \(CaO\) and \(NaOH\) are bases and absorb \(CO_2\) chemically.
Preparation. Heat a mixture of ammonium chloride and calcium hydroxide (slaked lime) in a dry test tube; the water formed must not run back onto the hot glass.
\(2NH_4Cl (s) + Ca(OH)_2 (s) → CaCl_2 (s) + 2NH_3 (g) + 2H_2O (g)\) conditions: heating.
Collection. Downward displacement of air only: \(M_r = 17\), density ratio 0.59. Never over water — ammonia is extremely soluble (about 700 volumes per volume at room temperature) and the water would rush up the tube.
Test. Damp red litmus turns blue. A glass rod dipped in concentrated hydrochloric acid, held near the mouth, gives dense white smoke of ammonium chloride: \(NH_3 (g) + HCl (g) → NH_4Cl (s)\).
Drying. Calcium oxide or soda lime, both basic. Concentrated \(H_2SO_4\) is wrong because it reacts to give ammonium sulfate; anhydrous \(CaCl_2\) is wrong because it forms \(CaCl_2·8NH_3\), a solid addition compound.
Preparation. Heat manganese(IV) oxide with concentrated hydrochloric acid; the acid is both reductant and source of chloride.
\(MnO_2 (s) + 4HCl (conc) → MnCl_2 (aq) + Cl_2 (g) + 2H_2O (l)\) conditions: heating.
Potassium permanganate with concentrated hydrochloric acid gives chlorine without heating: \(2KMnO_4 + 16HCl → 2KCl + 2MnCl_2 + 5Cl_2 + 8H_2O\).
Collection. Upward displacement of air (\(M_r = 71\), density ratio 2.45), in a fume cupboard. Never over water: \(Cl_2 + H_2O ⇌ HCl + HClO\), so the gas is both lost and contaminated.
Test. Damp blue litmus turns red and is then bleached, because the hypochlorous acid formed oxidises the dye. Damp potassium iodide–starch paper turns blue-black: \(Cl_2 + 2KI → 2KCl + I_2\).
Drying. Concentrated \(H_2SO_4\). \(CaO\) and soda lime would absorb the gas.
| Drying agent | Nature | Suitable for | Not suitable for | Reason |
|---|---|---|---|---|
| Concentrated \(H_2SO_4\) | strong acid, dehydrating | \(O_2\), \(H_2\), \(CO_2\), \(Cl_2\), \(SO_2\) | \(NH_3\) | acid–base reaction gives \((NH_4)_2SO_4\) |
| Calcium oxide (quicklime) | basic oxide | \(NH_3\), \(H_2\), \(O_2\) | \(CO_2\), \(Cl_2\), \(SO_2\) | acidic gases are absorbed as calcium salts |
| Soda lime | mixture of \(NaOH\) and \(CaO\), basic | \(NH_3\) | \(CO_2\), \(Cl_2\) | neutralises and absorbs acidic gases |
| Anhydrous \(CaCl_2\) | neutral salt, forms hydrates | \(O_2\), \(H_2\), \(CO_2\), \(Cl_2\) | \(NH_3\) | forms the addition compound \(CaCl_2·8NH_3\) |
| Silica gel / \(P_2O_5\) | physical or acidic dehydrating agent | most neutral gases | \(NH_3\) (\(P_2O_5\)) | \(P_2O_5\) is acidic and reacts with ammonia |
The rule behind the table: a drying agent must remove water without reacting with the gas. Choosing on that one sentence answers almost every exam item on drying.
A titration finds an unknown concentration by delivering a solution of known concentration from a burette until the indicator shows that the reaction is just complete.
For the reaction \(aA + bB →\) products the calculation is \(\frac{c_A V_A}{a} = \frac{c_B V_B}{b}\). For a monobasic acid and a monoacidic base this reduces to \(c_A V_A = c_B V_B\).
pH is defined as \(pH = -log[H^+]\). A 0.010 M solution of a strong monobasic acid has \([H^+] = 0.010\) mol/L and therefore \(pH = 2.00\); diluting it tenfold gives \(pH = 3.00\). At 25 °C, \(K_w = [H^+][OH^-] = 1.0 × 10^{-14}\), so a neutral solution has \(pH = 7.00\).
| Indicator | Colour in acid | Colour in alkali | Used for |
|---|---|---|---|
| Phenolphthalein | colourless | pink | weak acid with strong base; the colourless-to-pink change is easy to see |
| Methyl orange | red | yellow | strong acid with weak base |
| Universal indicator | red to orange | blue to purple | estimating pH, not for accurate titration |
The end point is where the indicator changes; the equivalence point is where the amounts of acid and base are exactly in the reaction ratio. They coincide only if the indicator's range lies on the steep part of the titration curve, which is why the indicator is chosen to match the salt formed, not the colour you prefer.
\(n = \frac{m}{M_r}\) \(n = cV\) (with \(V\) in litres) \(V = n × 22.4\) L at STP percentage yield \(= \frac{actual}{theoretical} × 100\%\) percentage error \(= \frac{|measured - accepted|}{accepted} × 100\%\)
Figure 1: a gas-preparation set-up. The reaction flask with a dropping funnel, a delivery tube, then collection. For NH₃ the collection tube is inverted because the gas is lighter than air.
Figure 2: upward and downward displacement of air. On the left the gas is denser than air, so it is delivered to the bottom of an upright jar and air leaves at the top. On the right the gas is lighter than air, so the jar is inverted and the gas is delivered to the closed end while air leaves at the open mouth at the bottom.
The delivery tube reaches the bottom of an upright jar so that the denser gas forms a layer under the air and lifts it out; if the tube stopped near the top, the gas would mix with the air and escape at the mouth. In the inverted jar the tube reaches the closed end for the same reason in reverse. In both cases the jar is left open — a stoppered jar would be pressurized by the incoming gas.
Figure 3: filtration. The filter paper is folded in half, then in half again, opened into a cone and pressed against the funnel wall; the stem of the funnel touches the inside wall of the beaker so the filtrate runs down without splashing.
Three details carry the marks: the paper must not rise above the rim of the funnel, the tip of the funnel stem must touch the beaker wall, and the mixture is poured down a glass rod so that it does not tear the paper. The residue stays on the paper, the filtrate passes through — so filtration separates an insoluble solid, and it cannot separate a dissolved salt from its solution.
Reading a set-up diagram in the exam. Trace the gas path from the reaction vessel to the collection vessel and check three things: is the vessel closed where it should be open, does the delivery tube reach the right depth, and is the collection method consistent with the density or solubility of the gas. Most "spot the error in the diagram" items are one of those three.
How do you distinguish O₂ from CO₂?
Solution: O₂ re-lights a glowing splint; CO₂ turns limewater milky (Ca(OH)₂ → white CaCO₃).
You have water, salt and sand: what are the separation steps?
Solution: add water, filter out the sand, then evaporate the filtrate to recover the salt.
A student reads a flask from above and records 20.5 mL instead of 20.0 mL. What error is this?
Solution: parallax error — the reading was not taken at the liquid level.
What mass of potassium chlorate is needed to produce 4.8 g of oxygen? (\(M_r\): \(KClO_3 = 122.5\), \(O_2 = 32.0\))
Starting from 12.25 g of potassium chlorate, a student collects 3.84 g of oxygen. Calculate the percentage yield.
10.0 g of calcium carbonate reacts completely with excess dilute hydrochloric acid. Calculate the volume of carbon dioxide at STP and the mass of calcium chloride formed. (\(M_r\): \(CaCO_3 = 100\), \(CaCl_2 = 111\))
25.00 mL of sodium hydroxide solution of unknown concentration needs 24.60 mL of 0.100 M hydrochloric acid to reach the end point with phenolphthalein. Calculate the concentration of the alkali.
The same student read the burette from above, so every reading was 0.10 mL too large. The titre was still calculated as final minus initial. What happens?
6.5 g of zinc is added to 100 mL of 2.0 M hydrochloric acid. Which reactant is in excess, and what volume of hydrogen at STP is produced? (\(A_r\): \(Zn = 65\))
A student records the volume of a flask as 20.5 mL when the true volume is 20.0 mL. Find the percentage error and say how it would affect a concentration calculated from that volume.
| Method | Separates |
|---|---|
| Filtration | an insoluble solid from a liquid |
| Evaporation | a dissolved solid from its solvent |
| Distillation | two liquids with different boiling points |
| Extraction | a solute from one solvent into another |
| Crystallisation | a pure solid from a saturated solution |
| Gas | \(M_r\) | Density relative to air | Solubility in water | Collection | Drying agent |
|---|---|---|---|---|---|
| \(H_2\) | 2 | 0.07 | very slight | downward displacement, or over water | \(H_2SO_4\), \(CaCl_2\), \(CaO\) |
| \(NH_3\) | 17 | 0.59 | very high, about 700 : 1 | downward displacement only | \(CaO\), soda lime |
| \(O_2\) | 32 | 1.10 | slight, about 0.03 : 1 | over water, or upward displacement | \(H_2SO_4\), \(CaCl_2\) |
| \(CO_2\) | 44 | 1.52 | appreciable, about 0.9 : 1 | upward displacement | \(H_2SO_4\) |
| \(Cl_2\) | 71 | 2.45 | reacts with water | upward displacement, fume cupboard | \(H_2SO_4\) |
Two questions decide the method. First, is the gas heavier or lighter than air — compare \(M_r\) with the average value 29 for air. Second, does it dissolve or react in water — if it does, water displacement is impossible and the gas must displace air instead. A gas that is both lighter than air and very soluble, such as ammonia, has exactly one option.
| Mixture | Technique | Why it works | Key apparatus |
|---|---|---|---|
| Sand and water | filtration | the solid is insoluble and is held on the paper while the liquid passes | filter funnel, paper, glass rod |
| Salt and water | evaporation, then crystallisation | water boils off at 100 °C; the salt is left and crystallises as the solution becomes saturated | evaporating dish, tripod, gauze |
| Water and ethanol | fractional distillation | ethanol boils at 78 °C and water at 100 °C, so the vapour is enriched in ethanol | fractionating column, condenser, thermometer |
| Iodine and sand | sublimation | iodine turns to vapour on gentle heating and re-forms crystals on a cold surface | evaporating dish, cold finger |
| Oil and water | separating funnel | the two liquids are immiscible and separate into layers by density | separating funnel, beaker |
| Copper sulfate from a solution with soluble impurities | crystallisation | the pure salt crystallises first as the solution cools; impurities stay in the mother liquor | beaker, evaporating dish, filter |
| Iron filings and sulfur | magnetic separation, or add \(CS_2\) | iron is attracted to a magnet; sulfur dissolves in carbon disulfide | magnet, or filter and evaporate |
| Two dissolved salts with very different solubilities | fractional crystallisation | the less soluble salt crystallises first on cooling | beaker, filter, thermometer |
| Observation | Conclusion |
|---|---|
| glowing splint relights | oxygen |
| squeaky pop with a lighted splint | hydrogen |
| limewater turns milky | carbon dioxide |
| damp red litmus turns blue | ammonia (an alkaline gas) |
| damp litmus turns red then white | chlorine |
| white smoke with a rod dipped in concentrated HCl | ammonia |
| white precipitate with acidified barium chloride | sulfate ion |
| white precipitate with silver nitrate, soluble in ammonia | chloride ion |
In the exam: lab items ask "which apparatus / which method / which observation" — memorise the triple (reaction, collection, test) for each gas.
| Mistake | Why it is wrong | Correction |
|---|---|---|
| Collecting \(NH_3\) by upward displacement of air | ammonia is lighter than air (\(M_r = 17\) against 29), so it rises out of an upright jar | invert the jar and deliver the gas to the closed end |
| Drying \(NH_3\) with concentrated sulfuric acid | an acid and a base react; the drying agent is consumed and the gas disappears as ammonium sulfate | use calcium oxide or soda lime |
| Drying \(CO_2\) with calcium oxide or soda lime | both are basic and absorb the acidic gas as carbonate | use concentrated sulfuric acid |
| Testing for \(CO_2\) with litmus paper | carbon dioxide is only weakly acidic and the colour change is faint and not specific | bubble through limewater and report "turns milky" |
| Collecting \(Cl_2\) over water | chlorine hydrolyses to hydrochloric and hypochlorous acids, so the yield falls and the sample is wet | collect by upward displacement in a fume cupboard |
| Stoppering a flask while gas is being generated, or heating a closed tube | pressure builds with no outlet and the vessel bursts | keep the system open; remove the delivery tube before the flame |
| Using dilute sulfuric acid on marble chips | calcium sulfate is only slightly soluble and coats the chips, so the reaction stops | use dilute hydrochloric acid |
| Reading a burette from above the meniscus | parallax makes every reading too large, and the error does not cancel if only one reading is affected | read at eye level, with a meniscus card |
| Writing "a gas was produced" as the observation | it does not identify anything and earns no mark | name the gas, give the test and the observation: "\(CO_2\); limewater turns milky" |
| Recording a titre to four decimal places from a burette | the instrument reads to 0.05 mL, so extra digits are invented precision | record 24.60 mL, not 24.6037 mL |
Which gas turns limewater milky?
Solution: CO₂.
Why is H₂ collected by downward air displacement?
Solution: because it is lighter than air.
Which method separates water from ethanol?
Solution: distillation.
What is the role of MnO₂ in preparing O₂?
Solution: a catalyst that speeds up the reaction without being consumed.
Why must the delivery tube be removed from the water before the burner is turned off?
Solution: as the flask cools the gas inside contracts, the pressure falls below atmospheric and water is pushed up the tube into the hot flask, cracking it. Removing the tube first breaks the liquid connection, so the pressure difference cannot draw water in.
Name a suitable drying agent for ammonia and explain why concentrated sulfuric acid cannot be used.
Solution: calcium oxide or soda lime. Sulfuric acid is a strong acid and ammonia a base, so they react: \(2NH_3 + H_2SO_4 → (NH_4)_2SO_4\). The gas is consumed instead of being dried. Anhydrous calcium chloride is also unsuitable because it forms \(CaCl_2·8NH_3\).
Calculate the mass of zinc needed to produce 240 mL of hydrogen at STP. (\(A_r\): \(Zn = 65\); molar volume 22.4 L/mol)
Solution: \(n(H_2) = 0.240 / 22.4 = 0.0107\) mol. From \(Zn + H_2SO_4 → ZnSO_4 + H_2\) the ratio is 1 : 1, so \(n(Zn) = 0.0107\) mol and \(m = 0.0107 × 65 = 0.70\) g.
What volume of 0.100 M hydrochloric acid neutralises 25.00 mL of 0.0800 M sodium hydroxide?
Solution: \(n(NaOH) = 0.0800 × 0.02500 = 2.00 × 10^{-3}\) mol. The reaction is 1 : 1, so the same number of moles of acid is needed: \(V = n/c = 2.00 × 10^{-3} / 0.100 = 0.0200\) L = 20.0 mL.
Limewater turns milky when carbon dioxide is bubbled through it, then clears when the gas is passed for a long time. Explain both changes with equations.
Solution: the first change is precipitation of calcium carbonate: \(Ca(OH)_2 + CO_2 → CaCO_3 + H_2O\). With excess carbon dioxide the carbonate is converted to the soluble hydrogencarbonate: \(CaCO_3 + H_2O + CO_2 → Ca(HCO_3)_2\), so the milkiness disappears. The gas is still carbon dioxide; clearing does not contradict the first test.
Which part of the meniscus is read in a burette, and what happens to the recorded volume if the eye is above the meniscus?
Solution: the bottom of the concave meniscus, at eye level. Reading from above makes the line of sight strike the scale higher than the true level, so every reading is too large; the titre, being a difference, is unaffected only if both readings are taken from the same position.
Why is chlorine tested with damp rather than dry litmus paper?
Solution: dry chlorine does not bleach. The bleaching agent is hypochlorous acid, formed when chlorine reacts with water: \(Cl_2 + H_2O ⇌ HCl + HClO\). The damp paper supplies the water, so the acid forms on the paper and oxidises the dye.
A reaction has a theoretical yield of 8.0 g and gives 6.4 g. Calculate the percentage yield, and state one practical cause of the loss.
Solution: \(6.4/8.0 × 100\% = 80\%\). Causes: product left on the filter paper or in the flask, incomplete reaction, or loss during transfer and drying.
Describe how you would separate a mixture of sand, sodium chloride and water, and name the apparatus for each step.
Solution: (1) stir the mixture with water so the salt dissolves; (2) filter through a filter funnel with paper — the sand stays on the paper as the residue, the salt solution passes through as the filtrate; (3) wash the residue with a little distilled water and dry it; (4) evaporate the filtrate in an evaporating dish to the point of crystallisation, then cool and filter the crystals. Sand is recovered as the residue, salt as crystals.
A student titrates with a burette that was rinsed with water and not with the acid. State the effect on the calculated concentration of the alkali and classify the error.
Solution: the water left in the burette dilutes the acid, so the acid that arrives is less concentrated than labelled and a larger volume is needed. The titre is too large, so the calculated amount of acid — and therefore the calculated concentration of the alkali — is too high. This is a systematic error, and repeating the titration will not remove it.
Explain why carbon dioxide is not collected over water even though it is only moderately soluble, while oxygen is.
Solution: oxygen dissolves to the extent of about 0.03 volumes per volume, so the loss is negligible; carbon dioxide dissolves to about 0.9 volumes per volume and part of it reacts with water to form carbonic acid, so a large fraction of the sample would be lost and the rest would be wet. Upward displacement of air gives a drier, more representative sample.
0.50 g of an impure sample of calcium carbonate gives 96 mL of carbon dioxide at STP with excess acid. Calculate the percentage purity. (\(M_r\): \(CaCO_3 = 100\))
Solution: \(n(CO_2) = 0.096/22.4 = 4.29 × 10^{-3}\) mol, equal to the moles of carbonate by the 1 : 1 ratio. Mass of pure carbonate \(= 4.29 × 10^{-3} × 100 = 0.429\) g. Percentage purity \(= 0.429/0.50 × 100\% = 85.7\%\).
Free · three languages · works offline